SawStop SAW-CNS175TGP252 CNS 1.75Hp, 115/230V, 60Hz, 10" Contractor Saw with 52" T-Glide Fence System

*You will be contacted in 24 hours with a shipping quote*

SawStop Saws Detect Contact With Skin

The blade carries a small electrical signal, which the safety system continually monitors. When skin contacts the blade, the signal changes because the human body is conductive. The change to the signal activates the safety system.

How It Works

Monitor & Detect

  • The blade carries a small electrical signal.
  • When skin contacts the blade, the signal changes because the human body is conductive.
  • The change to the signal activates the safety system.

Brake Activation

  • An aluminum brake springs into the spinning blade, stopping it.
  • The blade’s angular momentum drives it beneath the table, removing the risk of subsequent contact.
  • Power to the motor is shut off.

All this happens in less than 5 milliseconds!


Resetting the saw yourself is easy. Simply replace the blade and affordable brake cartridge and your saw is operational. The entire reset process takes less than five minutes.

Hobbyists, contractors, cabinet makers, DIY’ers, celebrities and educators choose SawStop everyday. It’s the no-compromise SawStop engineering that makes them choose these saws. The safety comes first, and is followed by unmatched quality, precision and meticulous engineering. SawStop saws are built to last, built to cut, and built to protect.

When SawStop appeared on the market in 2005, the saws took the industry by storm. We addressed a problem that seemed unsolvable, and that most had accepted as the norm. Media large and small, from Time Magazine to bloggers across the internet lauded this amazing marriage of innovation and quality.

The SawStop® Contractor Saw offers versatility and safety. Whether on the job site or in the shop, it delivers the performance you need with the peace of mind only SawStop's patented safety system can provide.

Motor: (all 60Hz, TEFC): 1.75hp
Cabinet footprint: 25 3/4" w x 27" d
Cast iron table: 20″ w x 27″ d
Cast iron table (w/ extension wings): 44″ w x 27″ d (w/opt. cast iron wings)
Extension wings: 12″ w x 27″ d each
Extension table 30 in rails: N/A
Extension table 36 in rails: 23 3/4″ w x 27″ d
Extension table 52 in rails: 40 1/8″ w x 27″ d
Weights - table saw only: 225 lbs
Weights - w/ 30 in fence systems: 245 lbs
Weights - w/ 36 in fence systems: 310 lbs
Weights - w/ 52 in fence systems: 335 lbs
Weights - (optional cast iron wings): 35 lbs each
Shipping weight (approx.): 240 lbs (table saw only)
Blade: 40-tooth, 5/8″ arbor
Blade diameter: 10"
Blade tilt: Left
Blade kerf: 0.118″ (3mm)
Blade plate thickness: 0.078″ (2mm)
Max. depth of cut, blade at 0º: 3 1/8″
Max. depth of cut, blade at 45º: 2 1/4″
Max. rip, right of blade - 30 in: 30 1/2″ (w/ 30″ rails)
Max. rip, right of blade - 36 in: 36 1/2″ (w/ 36″ rails)
Max. rip, right of blade - 52 in: 52 1/2″ (w/ 52″ rails)
Max. rip, left of blade: 16 1/2″ (w/ 30" Std. Fence)
Max. rip, left of blade (options): 12 1/2" (w/ T-Glide Fence)
Dado diameter: 8″ (req. dado brake + insert)
Dado max. width: 13/16"
Arbor diameter at blade: 5/8”
Main bearing size: 62mm OD x 30mm ID
Second bearing size: 52mm OD x 25mm ID
Table in front of blade (max. elevation): 10 5/8"
Table behind blade (max. elevation): 7 1/8″
Arbor Runout: 0.001″ Maximum allowable runout
Table flatness measured diagonally: 0.016″ Maximum gap
Blade alignment with miter slot: 0.010″ Maximum displacement
Deviation of miter gauge indexing stops from actual: ±0.25º
Alignment between splitter and blade: 0.010″ Maximum difference
Miter slots T-shaped: 3/4″ at top, 1″ at bottom, 3/8″ deep
Miter slots center: 11 1/8″ center-to-center
Miter slots info: 5 1/2″ (arbor flange to center of right slot)
Dust collection port diameter: 4″ under table top
Riving knife / splitter thickness: 0.090" (2.3 mm)
Blade guard (dust collection): N/A
Blade guard (micro guard): polycarbonate
Insert: zero clearance phenolic
Hand wheels: 6″ diameter, cast alum. w/ ABS handle
Belts: V-ribbed belt – static dissipative
Overall saw dimensions: 44" w x 39 1/4" d x 34 3/4" h (body only)
Overall saw dimensions 30 in: 58 1/2" w x 40" d x 34 3/4" h
Overall saw dimensions 36 in: 69 1/8" w x 45" d x 34 3/4" h
Overall saw dimensions 52 in: 85 1/4" w x 45" d x 34 3/4" h
Motor configuration 1: 1.75 hp, 110v, 14 A

***Shown with optional overarm dust chute, cast iron wings, mobile base, and casters.